Mantis "E" System User Manual download pdf (Page 4)

General Safety Rules

1. Never edge while people, especially children or pets are

nearby.

2. Before using, always visually inspect to see that the blade,

blade bolts and cutter assembly are not worn or damaged.

3. Do not start the motor when a bystander is standing in

front of the blade.

4. Do not put hands or feet near or under rotating parts.

5. Never lean over the rotating cutting head. Rocks or other

debris could be thrown into eyes and face and cause

serious personal injury.

6. Use extreme caution when reversing or pulling the edger

toward you

7. Make sure the blade has stopped before crossing surfaces

other than grass and when transporting the edger to and

from the area to be edged.

8. Never operate the edger with defective, missing or

incorrectly fitted guards.

WARNING

WHEN USING ELECTRIC TOOLS, BASIC SAFETY

PRECAUTIONS, INCLUDING THE FOLLOWING,

SHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK AND

PERSONAL INJURY.

Pay particular attention to all sections regarding safety.

Read and understand all these instructions before operating this

product and save these instructions. Be familiar with the

controls and the proper use of equipment.

For safe operations:

1. Keep work area clean.

Cluttered areas and benches invite injuries.

2. Consider work area environment.

Do not expose power tools to rain. Do not use power tools

in damp or wet locations. Keep work area well lit. Do not

use power tools where there is risk of fire or explosion.

3. Guard against electric shock

Avoid body contact with earthed or grounded surfaces,

e.g. pipes, radiators, stoves, ovens, refrigerators.

4. Keep children away.

Do not let visitors touch the tool or extension cord. All

visitors should be kept away from area. Local regulations

may restrict the age of the operator.

5. Store idle tools

When not in use, tools should be stored in a dry, high or

locked up place, out of reach of children.

6. Do not force the tool.

It will do the job better and safer at the rate for which it

was intended. Walk, never run.

7. Use the right tool.

Do not force small tools or attachments to do the job of a

heavy duty tool. Do not use tools for purposes not

intended; for example, do not use chain saw attachment to

cut tree limbs or logs.

8. Dress properly.

Do not wear loose clothing or jewelry that can be caught

in moving parts. Long trousers, non-slip gloves and sturdy

work shoes with non-skid soles are recommended when

working outdoors. Wear protective hair covering to contain

long hair.

9. Use protective equipment

To avoid injury, wear ear, eye protection, face or dust mask

if the operation is dusty. To avoid injury from falling

branches, wear helmet. Eye protection must meet ANSI Z

87.1 requirements.

10. Do not abuse the cord

Never carry the tool by the cord or yank it to disconnect it

from the socket. Keep the cord away from heat, oil and

sharp edges.

11. Maintain tool with care

Keep cutting tools sharp and clean for better and safer

performance. Follow instructions for lubrication and

changing accessories. Inspect tool cord periodically and if

damaged, have it repaired by an authorized service facility.

Inspect extension cords periodically and replace, if

damaged. Keep handles dry, clean and free from oil and

grease.

12. Disconnect tools

When not in use, before servicing and when changing

accessories such as blades, bits and cutters.

13. Remove adjusting keys and wrenches

Form the habit of checking to see that keys and adjusting

wrenches are removed from the tool before turning it on.

14. Avoid unintentional starting.

Do not carry a plugged in tool with a finger on the switch

trigger. Ensure switch is off when plugging in.

15. Use outdoor extension leads.

When tool is used outdoors, use only extension cords

intended for outdoor use.

16. Important extension cord information:

a. Make sure the extension cords are in good condition

before use.

1 2 3 4 5 6 7 8 9 ... 13 14

Comments to this Manuals

No comments

Mantis "E" System User Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools Mantis "E" System